Thursday, April 12, 2012

Op Pos 4-12-12

Back in TCL this morning....


Tuesday, April 10, 2012

Progress...end of day and 2,000 lbs lighter!



It now appears that I will need 3 tons of rock to finish all the borders.
I have 1 ton left.  I'll finish the north side of the drive tomorrow and then the south side next week.  Hopefully the weather will remain cool.

Driveway Border Underway

Border kit, some assembly required!






Monday, March 19, 2012

Brief mode refresher

The availability and channelization of the 5MHz amateur radio band has encouraged a lot of us to:
  • review our understanding of our principal modes of communications (AM, LSB, USB, and CW) and to;

  • reread our receiver (transceiver) documentation.
A Software Defined Radio (SDR) panadapter is a excellent way to "look at" each of these modes.

The panadapter display is a graphic representation of a radio frequency signal. The x-axis, reading from left to right, is frequency. The height of the graphic is signal strength. Figure 1, is an amplitude modulated (AM) signal on 3.740 MHz as indicated by the red line. Note you can see the carrier energy rising to -50 on the y-axis shown on the left hand side of Figure 1.

To the left and right of the carrier, you can see the lower side band and the upper side band respectively.


Figure 1 -- Amplitude Modulation (AM)







Source: KE4ID

Thursday, March 15, 2012

Zero Beat and Offset in CW

How to Zero Beat Another Station
by Jack Wagoner WB8FSV

CW stations should always try to zero beat each other. That means to adjust your rig's transmit frequency to exactly match the transmit frequency of the other ham you would like to talk to. Hearing two CW stations conduct a conversation a few hundred cycles apart is a waste of frequency space, and is inviting QRM. How does one zero beat another station? Easy to do on phone or SSB, just tune so that the other fellow's voice sounds normal. But trickier on CW because when you put your receiver exactly on a CW station's transmit frequency, you hear nothing, zero. In modern transceivers, in the CW mode, the receiver's BFO is offset from the displayed, transmit frequency in order to produce an audible tone. In other words, the transmit and receive frequencies are far enough apart for you to hear a pleasantly pitched tone when your transmitter frequency is tuned to exactly that of the ham you are listening to. This frequency offset is frequently about 600 Hz or Hertz.
Here is how I zero beat another CW station with my own rig, a Kenwood TS 450. I tune into, or sweep through, the other CW signal, the pitch going from high to low, until the other ham's CW signal disappears. Now my receiver is zero beat with the other ham's transmit frequency. But I want my transmit frequency to be zero beat with the other ham's transmit frequency. So then I tune again, with the other ham's pitch going from low to high, until I am 600 Hz away. For example, if the other ham's transmit frequency is 7137.90 kHz, I would tune my transceiver to 7137.30 (7137.90 minus .60 equals 7137.30.) to transmit exactly on his transmit frequency. The direction you tune or sweep, the pitch going either from high to low or going from low to high, is rig dependent. On Kenwood ham radios you would tune the pitch from high to low as you tune higher in frequency, to reach the 600 Hz offset and be zero beat with the others ham's transmit frequency.
I wrote the above paragraph several years ago, and currently I zero beat using a different method. I still have my Kenwood TS-450, but now as I tune around looking for a station to contact, I leave my RIT(receiver incremental tuning) turned on. Leaving your RIT on while tuning goes against convential wisdom, but I find it works for me. I leave my RIT on about 500 to 600 Hz up. When I discover another station I wish to zero beat, I tune by ear so that their CW tone drops down in tone to almost nothing, meaning that my transmit frequency is now approximately zero beat with theirs. Then I reset my RIT back up a few Hertz so that I can hear the other station. Takes me one or two seconds. Tuning by ear for an approximately 600 Hz tone just comes with experience. I have found that this method of zero beating works best for me. Recently I have become a DXing nut, and I find this new method faster for me. There is no one best method for zero beating. Whatever works best for you and for your rig.
This zero beat frequency stuff is pretty weird, it confuses me at times, and I hope I explained it correctly. The frequency offset for CW in most transceivers explains why when you are listening to a CW signal in the tranceiver's "CW" mode, and you switch to phone, to "LSB" or "USB," you loose the CW signal and have to go search a bit for it again.

Tuesday, March 13, 2012

FT2K Taking Shape

Ready for another "short" ConnectNow demo. Loaner still does not
provide telemetry nor echo but more and more functions are enabled
to send to the rig. Recent additions are the digital frequency display,
and scrolling with up and down arrow key. S-meter should be fully
operational when FT-2000D gets back from the shop.

Thursday, March 8, 2012

Sunday, March 4, 2012

MiniRig Continues to Evolve

Minirig now has real-time video feed from Cottage web cam.


Sunday, February 26, 2012

Wednesday, February 22, 2012

Tuesday, February 21, 2012

Robust Short Cut w/Authentication in URL

C:\Users\Carl\AppData\Local\Google\Chrome\Application\chrome.exe http://admin:password@thecottage.endoftheinternet.org/Set.cmd?CMD=SetPower&P60=0&P61=0&P62=0&P63=0

This mornings operating position....

Posted by Picasa

Sunday, February 19, 2012

Fences

Posted by Picasa

Round Table 2-3-2012

I thought you might like to hear yourselves as I hear you in Mentone. Jack starts us off. I have cut out my overs.

Friday, February 17, 2012

IP Address Changes

The Cottage Century Link ISP changes IP address more often than one might expect.
Recent change to router based DYNDNS.org update MAY make restoration of
lost connect move more quickly. However, I anticipate data flow will still be dropped
when Century Link changes IP address while traffic is active on the node.

Century Link tech supports reports that IP address changes are totally automatic and
WILL take place even if there is traffic on the node.

Posted by Picasa

Sunday, February 12, 2012

Needle Ice (Frost Columns) on a Desoto Park Trail

Click on title above for additional details.







Posted by Picasa

Cold on the Mountain

Posted by Picasa

FT-2000 60 Meter Channels

THIS WAS RECENTLY REPORTED ON A FT-2000 FORUM

It is very doubtful if it is possible change the operating band limits for 5MHz.
Allocations and modes are programmed into the CPU chip memory at manufacture
for the various markets and areas of use.

The control board is simply programmed by links which initiates the
appropriate pre-written data to meet the known authorised operating limits
in the various world markets. This is done from official data received at
the manufacturer.

These parameters form part of the type approval tests and are so are not
able to be re-written AFAIK.

It is unlikely that there is any route into the internal programming of the
CPU chip itself.

The firmware updates we are familiar with go into the DSP memory or separate
memory on the control board.

Wednesday, February 8, 2012

WEBRelay Web Instructions

WebRelay now in place. Using the WebRelay connected
to the Xmt Req plug on the back of the FT-2000D I can
now send a carrier from any location on the Internet.

Posted by Picasa

Obriensweb Feb 8, 2012